CableIQ™ Qualification Tester
Copper qualification tester troubleshoots and qualifies Ethernet network cabling speed (10/100/1000/VoIP).
- Works on live networks to provide Ethernet switch detection and device configuration
- Measure network capacity (10 Meg, 100 Meg, 1 Gig) to determine support for VoIP, data and video
- Advanced troubleshooting diagnostics; insertion loss, cross talk, noise issues
- Core troubleshooting features; length, distance to fault, graphical wire mapping, opens, shorts, power over Ethernet (POE) detection
- Tests all copper cabling media: twisted-pair, coax, and audio
- Locate and trace cables with digital toning technology. Requires IntelliTone 200 Digital Probe (included with CIQ-KIT)
View Product Demo
|Talk to an Expert||Where to Buy|
The network tech's vision into cabling bandwidth
Reduce escalated problems by as much as 30%
The network tech's vision into cabling bandwidth
CableIQ qualification tester is the first cabling bandwidth tester for network technicians. This Ethernet network cable tester gives even the most novice tech the vision to see what speeds existing cabling can support, quickly isolate cabling from network problems, and discover what is at the far end of any cable. That means network techs can close trouble tickets faster, reduce on-call time, and save money by better utilizing their existing infrastructure.
Reduce escalated problems by as much as 30%
CableIQ qualification tester's powerful network troubleshooting capability and intuitive interface enable your frontline technicians to identify and troubleshoot a wider range of problems within your network infrastructure. Is the port active? Are the duplex settings matched? Is it a network problem or a Ethernet cable problem? Can the Ethernet cable support the required network bandwidth? CableIQ network cable tester is the only Ethernet cable tester that can answer all these questions before trouble tickets are escalated to the next level reducing problem escalation by up to 30%.
When you deploy Voice over IP (VoIP) or Gigabit Ethernet, you want to make sure that the existing cabling will support the bandwidth requirements of your new equipment. Your cabling was certified, but moves adds and changes have rendered many links incapable of running desired speeds. CableIQ quickly reveals whether a link, including patch cords, is qualified for voice, 10/100BASE-T, VoIP, or Gig. Knowing your cabling's bandwidth capabilities before upgrading can prevent countless hours of future downtime and labor hours wasted on unnecessary troubleshooting.
See what speeds your existing cabling can support.
CableIQ's four-second Autotest clearly indicates with a check mark which speeds and applications the tested cable can run.
Plug into any cable, patch panel, or wall jack and see both the cable details (length/wiremap) and far-end device details (speed/duplex settings) at once. A series of both cable and network test functions help you isolate connectivity problems. For instance, if Discover mode shows duplex settings are matched but the problem persists, run Autotest to see if the cabling can support the required bandwidth. If a link is not qualified, CableIQ provides detailed information on the nature and location of cabling performance faults such as crosstalk or large impedance changes. With CableIQ your techs can close trouble tickets faster by cutting cable troubleshooting time in half.
Troubleshoot cabling faults in half the time.
This screen shot represents a cabling link that did not qualify for 1000BASE-T because of a connection fault at 4.1 meters.
Free up 10% or more of your switch ports
CableIQ's Discover mode shows you exactly what's at the far end of any cable. At the switch, test each cable one at a time. You can quickly see whether the cable is open at the far end, or is connected to a PC. Or use CableIQ's hub blink feature from the workstation to flash the corresponding switch port LED. You may be surprised at how many unused ports you can free up and redeploy using CableIQ.
Determine where installed cables are routed, all from one location.
Attach remote ID's in different locations, then perform multiple cable tests from the distribution center or wiring closet. CableIQ provides the wiremap, pair lengths, distance to fault, and remote ID number of each tested cabling link.
Intelligent wiremap tests for length, shorts, split pairs, or opens and displays with an intuitive graphical interface where a fault is located.
CableIQ's Intelligent Wiremap shows pin 6 open at far end of tested cable (130 ft/34 meters).
Locate cables and wires with superior accuracy
CableIQ supports IntelliTone digital toning by:
- Finding cables easier and tracing with better accuracy than any other tool on the market
- Toning and tracing safely on a live network
- Providing two digital tones and four analog tones
- Featuring IntelliTone cable mapping; after tracing, use the IntelliTone Pro Probe 200 to verify wiremap
Empower frontline techs with an easy-to-use-tool
Intuitive user interface and graphical display guides user with little or no training required.
- Rotary knob makes learning easy and operation simple you always know what test mode is selected
- Portable, lightweight, rugged ergonomic design for easy field use
- Four AA batteries - Long lasting battery life for several weeks of testing
- Remote adapter doubles as a protective endcap.
Customer quote: "I handed CableIQ to our level III techs, they turned the unit on and began testing within two minutes of reviewing the various available selections."
CableIQ Kit Choices
To maximize the value of your CableIQ ownership, choose one of our specialized kits. Each kit is tailored for qualification testing in specific work environments. Read on for detailed descriptions of each kit.
CIQ-KRQ, CableIQ Residential Qualifier Kit
The CableIQ Residential Qualifier Kit is designed for residential installers who need to document that cabling systems were installed properly and will perform reliably. It quickly qualifies home cabling networks to support voice, VoIP, 10/100/1000 Ethernet, and CATV. With included adapters, it replaces multiple tools for testing and troubleshooting all voice, data, audio/video, coax, and security wiring. Included CableIQ Reporter software allows installers to begin generating professional test reports immediately.
CIQ-KIT, CableIQ Advanced IT Kit
The CableIQ Advanced IT Kit is designed to maximize the efficiency of any cable qualification job. Use the included IntelliTone 200 Probe to find cables quickly and definitively, even on active networks. Use the included six smart cable IDs to perform a high volume of qualification tests in a short period of time. Each smart ID has the capability to perform a simple wiremap test or a full qualification test. Up to seven qualification tests can be performed without returning to the patch panel. The rugged carry case can be used to easily transport tools from one job to another.
CIQ-FTKSFP, Copper and Fiber Technician’s Kit
The Copper and Fiber Technician’s Kit is designed for the IT professional that works with both Copepr and Fiber Networks. It offers all of the advantages of the Advanced IT Kit but it also provides a way to test and verify your fiber connections with the Simplfiber Pro Power Meter and Light Source.
What is Qualification?
Qualification is a new category of testers designed to meet the emerging needs of network technicians who need to upgrade to higher network speeds as well as troubleshoot connectivity problems. Qualification testers, like Fluke Networks new CableIQ Qualification Tester, determines if an existing cabling link can or can not support certain network speeds and technologies. This differs from certification testers, like the DTX CableAnalyzer, which guarantees cabling installations comply with TIA/ISO performance standards and basic verification testers, like the MicroScanner Pro, which tests if the cable is connected correctly.
Qualification testers allow network technicians to perform a series of troubleshooting steps to better isolate cabling from network problems. For example, a first step in troubleshooting a network connectivity problem might be to check the speed and duplex settings of connected devices. If the tester shows the settings are matched, but the problem persists, a qualification test can be performed. Performing a qualification test will allow the technician to identify whether insufficient cabling bandwidth is the cause of the problem. Knowing your cabling's bandwidth capability allows you to close trouble tickets faster and helps ensure seamless upgrades to higher network speeds.
Choosing the right tool for the job
When to use a qualification tester: If you are a network technician, and need to see whether the existing cabling will support your 1000BASE-T network, a qualification tool is the right choice. If you need to troubleshoot connectivity problems and isolate cabling problems from network problems, then qualification is the perfect solution. If you have an existing network and are doing small adds, moves, and changes, or are setting up a temporary network and just need to qualify it for a specific network technology, a qualification tool is a good option.
When to use a certification tester: If you're a commercial installer or network owner who needs to prove that all cabling has been installed correctly, and meets TIA or ISO link specifications, you must certify it. If you are in a troubleshooting environment, and need to show unequivocally that the link under test is failing category 5e or 6 performance requirements according to TIA or ISO standards, your only choice is a certification tool. If you have a mixture of fiber and copper cabling, and often need to test both, cable certification tools do that best.
To receive the support and financial security of a manufacturer's warranty, certification to TIA/ISO standards is your only option. Anything else makes the installer liable for the performance of the installation which can be quite costly. For example, a large 1000 link installation could represent a $100,000 (USD) project, which can be a hefty liability if manufacturer warranty is not obtained.
When to use a verification tool: Verification tools are typically used by any technician who pulls and terminates cable or performs basic moves, adds and changes. These tools are used as a first line of defense in finding connection and wire-pairing faults.
Models & Accessories
CableIQ, RJ-45 patch cord (2), RJ-11 patch cord (2), bare wire adapter, speaker wire adapter, coax cable, coax BNC adapter, coax RCA adapter, “Qualified” labels (50) and a soft carrying case See Photo
CableIQ Service Kit includes CableIQ Qualification Tester, six CableIQ Remote Identifiers, CableIQ Reporter software CD, RJ45-RJ45 shielded patch cords (2), USB cable, coax “F” push-on cable, RJ45/RJ11 universal coupler, LinkRunner Network Multimeter, LinkRunner main wiremap adapter, Intellitone Digital Probe 200, test accessory soft pouch, owners CD and quick start guide, packaged in a rugged carrying case; one (1) 9V and six (6) AA batteries included. See Photo
*This SKU has been discontinued but product support will continue through September 23, 2017
CableIQ Advanced IT Kit Includes CableIQ main unit with remote adapter, CableIQ Reporter software CD, IntelliTone 200 Digital Probe, Remote IDs #2-7, (2) RJ45-RJ45 patch cord, USB cable, coax 'F' push-on adapter, 75-ohm coax patch cord, RJ45/11 universal coupler, RJ11-RJ11 patch cord, owners CD and quick start guide, (4) AA batteries, test accessory soft pouch, duffel style bag. See Photo
Copper and Fiber Technician’s Kit – Includes the CableIQ (CIQ-KIT) and SimpliFiber Pro (FTK1000) Fiber Test Kit. See Photo
CableIQ Qualification Tester Includes CableIQ with remote adapter, CableIQ Reporter software CD, (2) RJ45-RJ45 patch cord, USB cable, coax 'F' push-on adapter, owners CD and quick start guide, (4) AA batteries, soft carry case
Micro IT kit soft carry duffle
CableIQ Coax Adapter Kit includes F-connector, BNC and RCA connectors
CableIQ Remote Identifier Kit includes remote identifier numbers 2-4
CableIQ Remote Identifier Kit includes remote identifier numbers 5-7
RJ45/11 Modular Adapter
CableIQ Speaker Wire Adapter
CableIQ Main Wiremap Adapter (replacement part for lost or damaged unit)
IntelliTone 200 Probe Includes: IntelliTone 200 Probe, RJ11 and RJ 45 patch cables, lanyard, quick start guide, and 9 volt battery
Cable types supported
UTP, STP, FTP, SSTP, RG6, RG59, audio and security
1000BASE-T, 100BASE-TX, 10BASE-T, VoIP, 1394b S100, TELCO, Wiremap only, Coax
Wiremap, length, cable signal performance, digital toner, analog toner, Ethernet port detection and identification, analog telephone detection, blink port light, continuity, speaker test, cable fault finding, video signal detection.
Can detect single wire faults and supports MultiMap mode with up to seven remote office identifiers. Draws proportional wire length to breaks. Detects split pairs.
Measures crosstalk and impedance and compares against appropriate limits based on qualification test selected. Detects location of large point sources as well as distributed sources in the cabling if they are sufficient to disqualify the application
Up to 250 qualification test results
Battery type: 4 AA (NEDA 15A, IEC LR6) alkaline batteries
20 hours of typical use, without backlight
Other battery types supported
4AA photo lithium, NIHM, NICAD
Dimensions and weight
7in x 3.5in x 1.75in (17.8cm x 8.9cm x 4.5cm) 1.2 lb (0.55 kg)
CableIQ Qualification Tester Brochure
CableIQ Telecom Data Sheet
Fluke Networks Solution Catalog
The Guide for selecting and ordering Fluke Network Solutions and Products
Fluke Networks 4 Page Catalog
Ethernet In A Harsh Environment - White Paper
Whitepaper that discusses the unique issues that can arise when you deploy Ethernet in an industrial environment, and how to avoid production downtime caused by these issues.
Whitepaper: Troubleshooting Your Industrial Network
Gold Product Support
Gold Support for your CableIQ Qualification Tester allows you to make the most of your purchase while ensuring a higher return on your investment. You will minimize your downtime, receive faster trouble resolution and have total access to all support resources.
What do you get with Gold Support for your CableIQ Qualification Tester?
Repairs and loaner equipment - If your CableIQ should fail, we'll deliver a loaner unit via next business day delivery to keep you up and running. We'll repair your CableIQ and replace defective or faulty accessories at no charge, with first on bench" priority, and return it to you - all shipping paid by Fluke Networks.
Access to live 24 x 7 technical support - Extend the expertise of your staff. Gold Support includes direct, immediate telephone access to our world-class Technical Assistance Center (TAC), direct access only available to Gold Members. Our centers in Seattle, WA and Eindhoven, NL employ a full staff of highly trained technical experts that are on call, including weekends and through the night when most network changes are implemented, to answer complex troubleshooting questions helping you get the most out of your CableIQ and understand the results you are seeing.
Accessory Replacement - Some accessories are essential to your CableIQ. The normal warranty on accessories is 90 days, but parts and accessories that shipped with your tester will be replaced free of charge with Gold Support once qualified as defective by our technical assistance center.
Unlimited access to our Knowledge Base - You'll have an open door to valuable proprietary information we've gathered from helping customers over the years. It also includes helpful technical articles written by our experts.
Member Only promotions - Your membership qualifies you for Members Only promotions and programs. This includes product discounts, access to reconditioned equipment at special prices and other incredible values.
Ensure that you are getting the most out of your CableIQ Qualification Tester with Gold Support Services.